Car Shaking While Driving? 5 Common Causes and How to Fix Them

Car Shaking While Driving
Car Shaking While Driving
Credit: Shutterstock

Pay attention to your car if it shakes while driving, before the problem worsens.

A car can shake, vibrate, or wobble for many reasons, but you can narrow down the cause by watching for a few signs. This guide explains five common causes, how to narrow down the problem, and which you can repair yourself.

Caution: Don’t keep driving if the vibration starts suddenly or becomes severe. Pull over safely and inspect the vehicle.

Use this Master Table to Narrow Down the Cause of Shaking

Note: These are clues, not final diagnoses. More than one fault can produce similar symptoms.

When does the car shake? Check these
At a certain road speed Tires, wheel balance, wheel runout, or bent wheels
Mostly at highway speed Tire and wheel balance or tire damage
Only when braking Brake rotors, hub runout, calipers, and suspension
Mainly during acceleration CV axles, driveshaft, U-joints, or engine mounts
At idle Engine, misfire, or engine/transmission mounts
After hitting a pothole Tire damage, bent wheel, suspension, and alignment
Soon after a tire change Wheel balance, wheel seating, and lug-nut torque

Cause 1. Tire or Wheel Problems

Tire and wheel problems are among the most common causes of vehicle shaking, especially when the vibration worsens as you drive faster. Common causes include an unbalanced tire, a bent wheel, uneven tire wear, or tire damage.

To confirm if the tire or wheel is the culprit, look for these signs:

  • Shaking gets stronger at highway speeds.
  • The steering wheel, seat, or floor vibrates.
  • A tire has uneven or cupped tread.
  • The problem started after hitting a pothole or curb.
  • The shaking started after tire or wheel replacement.

How to Fix It

Start by checking the tire pressures and inspecting each tire for bulges, cuts, uneven wear, or other damage.

If the tires look okay, have the wheels balanced. If the vibration remains, ask a tire shop to check for a bent wheel, tire runout, or an out-of-round tire. Replace any damaged tire or badly bent wheel.

Do not assume you need a wheel alignment just because the car shakes. Bad tires or wheels cause speed-related vibration in 90% of cases.

Cause 2. Faulty Steering or Suspension Parts

Loose or worn tie rods, ball joints, control-arm bushings, shocks, struts, and wheel bearings can make the car wobble, wander, or shake, especially over bumps.

Here are the signs to confirm if defective steering or suspension parts are causing the car to shake:

  • Loose or vague steering
  • Clunking over bumps
  • Uneven tire wear
  • The car wanders on a straight road
  • Shaking gets worse on rough roads
  • Humming or growling from a wheel

A worn wheel bearing can cause vibration, but it more often produces a humming or growling noise that changes with speed or while turning.

How to Fix It

Have a mechanic check the steering and suspension for loose or worn parts. Replace only the component that has been confirmed faulty.

If you replace tie rods, ball joints, control arms, or other parts that affect wheel position, the car will usually need a wheel alignment afterward.

Do not work under a vehicle supported only by a jack. Use properly rated jack stands or have a repair shop do the inspection.

Cause 3. The Brakes Are Causing the Shake

If the car drives smoothly but starts shaking when you press the brake pedal, the braking system is likely the culprit. The vibration may come from uneven rotor wear, excessive rotor runout, worn brake pads, a sticking caliper, or looseness in the wheel or suspension.

You might feel the brake pedal pulsing, the steering wheel shaking during braking, or the vibration getting worse during hard braking or when slowing from higher speeds.

How to Fix It

Take it to a mechanic to inspect the brakes for worn or uneven rotors, damaged pads, and sticking calipers. Depending on the cause, the repair may involve replacing or resurfacing the rotors, replacing the brake pads, or servicing the caliper.

If brake work doesn’t solve the vibration, also check the wheel bearings and suspension for looseness.

Cause 4. CV Axle or Driveshaft Problems

If the car shakes only while accelerating and becomes silent when you let off the gas, the problem may be in the drivetrain.

On front-wheel-drive cars, a worn inner CV joint is a common cause. On rear-wheel-drive and all-wheel-drive vehicles, the driveshaft, U-joints, or center support bearing may be responsible.

To confirm the cause, look for these signs:

  • Shaking gets worse during acceleration.
  • The vibration becomes weaker when coasting.
  • You hear clicking while making tight turns.
  • You hear clunking when accelerating or slowing down.
  • A CV boot is torn or leaking grease.
  • You feel a strong vibration through the floor.

How to Fix It

A worn CV joint or axle usually needs professional replacement. Driveshaft problems may require replacing a U-joint, support bearing, or the driveshaft itself. Because driveshafts rotate at high speed, a qualified mechanic should inspect and repair damaged or bent driveshafts.

Cause 5. Engine, Transmission, or Mount Problems

If the car shakes at idle, the vibration fluctuates with engine RPM, or you feel a thump when shifting into Drive or Reverse, the problem may come from the engine, transmission, or their mounts.

How to Fix It

If the engine runs rough or the check-engine light is on, scan for trouble codes and diagnose the engine problem first.

If the engine runs smoothly but the cabin still vibrates, have a workshop inspect the engine and transmission mounts.

A flashing check-engine light can indicate a serious misfire, so avoid hard driving and have the car checked as soon as possible.

What You Can Check and Fix at Home

You can safely perform the first part of the diagnosis without removing any major components. This may include:

  • Checking cold tire pressures.
  • Inspecting tires for bulges, cracks, separation, and uneven wear.
  • Looking for obvious wheel damage.
  • Confirming that wheel nuts are torqued to the manufacturer’s specification.
  • Looking for torn CV boots and obvious grease leakage.
  • Recording exactly when the vibration occurs.
  • Scanning diagnostic trouble codes if the check-engine light is on.

More advanced work usually requires a workshop visit. A technician will use equipment to balance wheels, perform road-force testing, measure runout, check brakes, inspect suspension, check hubs, and diagnose the driveshaft.

The Bottom Line

When a car starts shaking, don’t replace parts at random.

  1. If it follows road speed, check the tires and wheels first.
  2. If it happens while braking, inspect the brakes.
  3. If it happens under acceleration, check the drivetrain.
  4. If it comes with loose steering, clunks, or wandering, inspect the steering and suspension.
  5. If it follows engine RPM or happens while the car is stopped, look at the engine and its mounts.